technicalside cross-posted this post in Hive Motors 2 years ago


Rebuilding Nissan NP300 Pickup Gearbox

in OCD2 years ago (edited)

Daily log file of what I do on a daily basis I enjoy and have a huge passion for what I do its very satisfying to see that what you built is working as intended. Even though its hard labor I still head home with a satisfying smile

Another day another dollar they say. Maybe not when jobbing for someone😂!

Today I assembled a Nissan gearbox, one of the easy ones, and probably the easiest, second to the Nissan/Renault NP200 gearbox combination.
(Its certainly less of a Japanese product then it is French!)

The fun part about assembling this specific gearbox is the low effort and quick assembly time, it doesn't have a lot of press work that needs to be done, a little heat and some stuff might fall into place.

Sorting all of the components is highly recommended even though a lot of people don't ever bother doing that, they just grab from the bucket, I personally think a person is more productive and effective when everything is sorted. You know exactly what is missing before starting the assembly and when the next part is needed it can be quickly installed.
Before starting the assembly re-inspect all of your components again to verify that you have not missed any parts that might be worn out.

IMG_20220811_102902.jpg

Its very crucial for all of these small parts to be put back in the correct places in the correct manor, even though these parts are important the gearbox will function as intended if some parts are left out, but it will prematurely wear and probably end back up in your shop within 3 to 6 months.
Now unless you absolutely adore working that's a big don't want.

IMG_20220811_102907.jpg

Most of the replacement parts for this specific job. even though 4th gear was completely burned, it was saveable by just a complete bearing overall some syncro-rings, oil seals and a new input shaft along with a new 4th gear for the cluster.

IMG_20220811_105407.jpg

The new 4th gear for the cluster along with the new bearing and input shaft, prepping what's needed for the assembly so that it can be fit and go.

IMG_20220811_105316.jpg

Had some pressing work to do in order to remove and replace the 4th gear on the cluster shaft (Countershaft) Old 4th gear removed, added the new 4th gear then add the cluster bearing.

"Don't forget the cir-clip I mumbled to myself"

IMG_20220811_104305.jpg

I like to puzzle it out in its shape, making sure every hub and sleeve are the right way around because the grooves differ from side to side, some don't even have grooves.
This is also more or less how it would shape out with 5th gear and reverse falling on the left side of the mid plating.

IMG_20220811_111906.jpg

The 3rd gear is the 1st to go onto the main shaft, ironic is it not?
Sometimes the hub just presses over the shaft very easily and can be done with the hand, other times you need a dolley shaft and use a little bit of force with a small hammer and it should pop right over.

IMG_20220811_112047.jpg

Once your 3rd gear and hub is in place, flip the main shaft upside down then add your 2nd gear and hub and sleeve along with the spring dog clips, then add 1st gear. Always lubricate the syncro-rings or any parts where two metal surfaces touch each other.

IMG_20220811_113843.jpg

We like to remove the sidewall seals of the bearings, seeing that they run in oil and that the grease will be washed out in any-case its not bad to do that at all, although it has no downside in leaving the seals or sidewalls in place.

IMG_20220811_105644.jpg

Heating up the inner ring of the bearing in order to slide the main shaft into its correct place, it can be pressed into place, I personally find this method faster and more effective.

IMG_20220811_114527.jpg

After you insert it into place keep holding it in place for a few seconds and wait for the metal to cool down a bit and tighten around the shaft.

IMG_20220811_114719.jpg

I can now add the input shaft that has the 4th gear pressed onto it, which means the 4th gear is one with the input shaft where as the other gears are able to spin freely on the main shaft.

IMG_20220811_122654.jpg

Adding the cluster shaft or counter shaft alone can sometimes get tricky but it is possible, if someone is nearby I generally ask for help, if not ..well...
The process behind it is quite confusing and tricky and hard to take photos of doing. I'll explain it a bit more of it another time.

IMG_20220811_123237.jpg

Once the cluster shaft is firmly in place I can now start adding the reverse gear and the 5th gear and start bolting everything into place. This is where it starts looking like something proper. A few more steps and the job is done!

IMG_20220811_135450.jpg

Once everything is bolted to correct specs, I can now add the selector shafts from the bottom up and remind myself not to forget the shaft restrictors😂 otherwise it might slip into reverse from 5th gear.

IMG_20220811_143009.jpg

I always add the front bell housing casing first because some sleeves can be accidentally selected and some small parts like dogs clips can fall out and cause you to start from scratch, and that will be no fun.

IMG_20220811_144341.jpg

Added the tail piece or extension housing and its all done and ready to be installed into the motor vehicle.
Remember when installing a gearbox and there's a lot of struggling going on, its safe to assume that something is not right, etc dell pins, out of line, or clutch miss aligned. a gearbox would 99% of the time fall into place if installed correctly.

IMG_20220811_151721.jpg

To everyone who made it this far into my lengthy post Thank you for the read and the support.

If you found this entertaining or educational please consider a re-blog and up-vote

Power House Creatives Logos FINAL.png

Connecting the people of #HIVE across South Africa. #hive